Tutorial · Beginner
Grow lights for seedlings: types, distance and hours
A sunny window rarely gives seedlings enough light in late winter, which is why window-grown starts get tall and floppy. A simple white LED or fluorescent shop light, hung close and run on a timer, is the single best seed-starting upgrade.
Steps
- Choose the light type: white full-spectrum LED shop lights or bars (best all-round), or T5/T8 fluorescent tubes (cool white or daylight). Skip incandescent and halogen bulbs — they run hot and have the wrong spectrum.
- Pick a color around 5000–6500K (“daylight”), or pair one cool-white and one warm-white tube. White light contains the blue and red seedlings use and lets you spot problems.
- Size it to your trays: one 4-ft fixture spans two 10×20-in flats end to end. Light the whole tray evenly — seedlings at dim edges lean and stretch.
- Hang it on adjustable chains or hooks. Fluorescent tubes: 2–4 in above leaves (up to about 6). Typical LED shop lights: about 2–6 in. High-output LED panels: follow the maker’s hanging chart, often farther.
- Plug it into an outlet timer for 14–16 hours a day. Seedlings need a dark period, so don’t leave lights on around the clock.
- Lights can stay off until most seeds sprout (except light-needing seeds like lettuce and dill), but must go on the moment sprouts appear.
- Raise the light as plants grow to keep the same gap, and check daily for stretching or bleaching.
- Run a small fan for short periods each day: gentle airflow builds sturdier stems and helps prevent damping-off.
Signs of too little light
Tall, thin, pale stems with wide gaps between leaves, and seedlings leaning toward the light. Lower the light, add a second fixture, or lengthen the day to 16 hours.
Signs of too much light or heat
Bleached, white, yellow or crispy patches on the leaves nearest the light. Raise the fixture a few inches.
Lumens, watts, PPFD and DLI
Lumens measure brightness to human eyes and watts measure power, so both are only rough guides. Plant-usable light is PPFD (µmol/m²/s at the leaves) and the daily total is DLI (mol/m²/day). Most vegetable seedlings do well around 8–14 DLI, which at 16 hours of light is about 140–245 PPFD (DLI = PPFD × hours × 0.0036). For fluorescent tubes, NC State gives 10–15 lamp watts per square foot for germinating seeds and 15–20 for growing seedlings — two 40-W, 4-ft tubes over a 1×4-ft strip is about 20. Iowa State suggests high-output 4-ft LED fixtures of at least 3,000 lumens for indoor plants needing medium-to-high light.
What to buy (no brands needed)
A white full-spectrum LED or daylight T5/T8 fixture (about 5000–6500K), a listed PPF/PPFD value if available, enough length to cover your trays, adjustable chains, and an outlet timer. Optional: a thermostat-controlled heat mat for warm-season crops and a small fan. Replace fluorescent tubes every 1–2 years as they dim.
For experienced growers
If you have a light meter (or the maker’s PPFD map), set hanging height to reach your DLI target in 14–16 hours rather than running longer. UNH notes that ordinary T8 shop lights can need very long days to hit ideal DLI for sun-loving seedlings — a sign they should be closer or brighter. Pink red-blue LEDs work but make it hard to judge leaf color.
Sources
Guidance follows university Cooperative Extension recommendations. Ranges are general; varieties, soils and microclimates differ. Your county extension office can give local advice.
- University of Minnesota Extension — Starting seeds indoors
- University of Minnesota Extension — Lighting for indoor plants
- yardandgarden.extension.iastate.edu — Sources supplemental light indoor plants
- extension.umd.edu — Starting vegetable seeds indoors
- extension.unh.edu — Optimizing plant growth indoor lighting qa
- hortscans.ces.ncsu.edu
- spes.vt.edu